Shop All

The 2 Motor Drivetrain Gearbox - Through Bore Bundle contains the REV-21-2190 base kit, the 20DP Gears needed for a 6in wheel ratio, and 20DP NEO Pinions Gears (10T, 11T, 12T) for multiple speed options. If a 4in or 5in wheel gear ratio is needed,...

The #25 Chain Turnbuckle is compatible with both the REV ION System and REV DUO System. It is designed to adjust the length of a #25 Chain by replacing a few links in a run and also allows the user to tension the chain by adjusting...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications Length: 30cm Notes As of 01/10/2024, the length on this product page has been corrected from 15cm to 30cm...

The 3in MAXSwerve Module Wheel Hardware Pack was designed for the 3in MAXSwerve Module. This kit is for FRC teams looking to streamline their wheel maintenance at competitions. With this kit, teams can pre-build their wheel assemblies, making...

Connect the REV Through Bore Encoder directly to the SPARK MAX Data Port using this adapter. This adapter connects the Absolute Duty Cycle output of the Through Bore Encoder to the correct SPARK MAX Data Port pins, leaving the incremental quadrature...

This product is a 6:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 5:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 3:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 2:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 1:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

New and improved, the Mecanum Drivetrain Kit V2 gives teams all the parts needed to build a Mecanum Drivetrain for use within robotics programs like FTC. This updated kit uses Ultra 90 Degree Gearboxes to place the UltraPlanetary HD Hex Motors within the...

The MK Battery ES17-12 is commonly used in FIRST Robotics Competition robots. Specifications Manufacturer: MK Battery Voltage: 12V Capacity: 18AH (20 Hour Rate) Product Dimensions: 7.13in x 2.99in x 6.57in Weight: 12.89lbs Documentation MK...

Dead Axle Tube is compatible with the REV ION System and can be used with 3/4in Needle Bearing Carrier (REV-21-2385) and MAXSpline Shaft (REV-21-2520) as the dead axle in a dead axle roller. Can also be used with custom rollers and as...

The 1in Pivot Joint is compatible with the REV ION System. Create a pivot joint at the end of a piece of MAXTube - 1x1 with Grid Structure. Specifications Material: POM (Acetal/Delrin) Documentation REV ION Build System Documentation Introduction...

The MAXSpline Shaft is compatible with the REV ION System. The shaft is an extruded aluminum MAXSpline that provides a high strength alternative to 1/2in hex shaft that can interface with any REV ION System components with a MAXSpline bore. The...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0. Applications ...

The WAGO 221 Inline Splicing Connector is a robust and easy to use splicing connector that makes fiddling with hard-to-master crimp-style connectors a thing of the past. Simply lift the lever up, insert the stripped wire, and push the lever back down to...

The REV Mini Power Module (MPM) is a compact power distribution module that allows you to securely and quickly power peripheral devices to your robot. Need more low-current channels on your PDH? Wire the MPM to one of the high-current channels on the PDH...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...

REV Robotics custom ATO sized auto-resetting breakers are designed to give reliable protection for FRC robot actuators.  These custom developed breakers adhere to SAE Standard J553 and will give consistent performance even after hundreds of breaker...