Cables

This 4-pin JST PH to 4-pin roboRIO I2C Cable is designed to connect REV I2C sensors, like the REV Color Sensor V3, to the I2C port on the NI roboRIO for use in the FIRST Robotics Competition. Each cable is approximately 36 inches long. This cable...

The JST PH 6-pin to 4 Channel PWM Cable allows for seamless connection of the Through Bore Encoder into the FRC control system (roboRIO).

These SPARK PWM Cables have a JST-PH 4-pin connector on one end, and a 0.1in 3-pin female PWM connector on the other. They are designed to convert the SPARK MAX Motor Controller's PWM/CAN port to a standard 3-pin PWM port on a robot controller. The black...

The REV POE Injector Cable was specifically designed to address a common problem for many FRC teams with their wireless radios: intermittent power glitches. The wireless radios used in the last several FRC seasons can be powered either through a...

The JST PH 6-pin Joiner Boards (REV-11-1277-PK4)  are intended to be used with the JST PH 6-pin Extension Cables to extend the reach of your NEO Brushless Motor sensor cables. The JST VH 2-pin Joiner Board - 4 Pack (REV-31-1429-PK4) are small...

The SPARK Flex Data Port Breakout Cable (REV-11-2853) breaks out the default pin functions of the SPARK Flex Data Port into commonly used connectors for external sensors. The keyed and locking Data Port connector ensures a secure and aligned fit when...

The USB-A to USB-C 2.0 Cable - 2m (REV-11-1232) is a longer version of the USB-A to USB-C cable included with the SPARK MAX Motor Controller and the Control Hub. Use this cable to connect your SPARK MAX or Control Hub to a standard computer from up to 2...

Absolute Encoder Adapter (REV-11-3326) connects the REV Through Bore Encoder directly to the SPARK MAX Data Port. This adapter connects the Absolute Duty Cycle output of the Through Bore Encoder to the correct SPARK MAX Data Port pins while leaving the...

The 36in PWM Cable - 4 Pack (REV-11-1130-PK4) is an ideal servo extension, providing a 3ft reach for servos, sensors, and other PWM-controlled devices. Featuring a universal 3-pin design with a female connector on one end and a male connector on the...

2-pin header cable that can be used for connecting signals, sensors or any other spots on robots. Features 2 female 0.1in pitch connectors on each end.  Specifications Length: 91cm (36in) 2 pin receptacle on 0.1in pitch Wire Colors: red, black 22...

The Molex MicroFit+ Power and CAN Cable is the dedicated replacement and accessory cable for the MAXSpline Through Bore Encoder. It provides both power and CAN connectivity through a compact, secure 2x2 Molex MicroFit+ latching connector. While currently...

The 36in CAN Extension Cable is a 3-pin connector to interface with existing CAN devices.  Specifications Length: 36in (3ft) Wire Colors: yellow, green 22 AWG

This JST-PH 6-pin Breakout Board is designed to adapt external sensors to the SPARK MAX 6-pin Encoder Port standard. It features a JST PH 6-pin connector, labeled solder pads, and through-hole pads that are compatible with popular 63R style quadrature...

These plastic clips are designed to keep standard 0.1" 3-pin PWM connectors together. Simply clip them around an assembled pair of connectors.

The NEO 2.0 Sensor Cable connects the NEO 2.0 Brushless Motor’s sensor port to a standard JST PH 6-pin interface used on REV motor controllers. The 2x3-pin PHSD connector provides a secure, latching connection at the motor, while the 6-pin JST PH...

The CAN Terminator Pack provides two compact, plug-ready termination options for teams looking to maintain reliable CAN bus performance anywhere in their robot’s wiring. Each terminator uses a small 10mm x 10mm internal circuit board sealed with...

The MAXSpline Grommet provides a simple way to route wires through MAXTube while preventing abrasion against bare aluminum. Made from pliable 60A rubber, it press-fits into the MAXSpline Bore on MAXTube with a 1/8 inch wall, creating a clean pass-through...

The SPARK MAX Data Port Breakout Board makes it easy to connect external sensors to the SPARK MAX Data Port. For additional information on the SPARK MAX Data Port, please take a look at the SPARK MAX User's Manual. Analog Input Issue - Affects Rev. A...

This update to the SPARK CAN Cable bridges the H and L CAN signals together within the cable itself. This prevents the CAN Bus breaking in the event of a cable disconnecting from a SPARK MAX Motor Controller. These SPARK CAN cables have a JST-PH 4-pin...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications REV-11-1275-PK4: Length: 90cm (35.5in) REV-11-3327: Length: 30cm (11.81in)