FTC Discounts

The REV Robotics Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will...

Easily connect multiple devices to your robot battery with the XT30 Power Distribution Block. Allows for clean, compact wiring of all your XT30-connected devices. Compatible with: Expansion Hub, Blinkin LED Driver, SPARKmini, Servo Power Module, and many...

The #25 Chain Turnbuckle is compatible with both the REV ION System and REV DUO System. It is designed to adjust the length of a #25 Chain by replacing a few links in a run and also allows the user to tension the chain by adjusting the...

The 15mm Extrusion Lift Kit offers an assortment of components needed to build an un-powered 3-stage continuous or cascading lift. The basics of the linear motion kit can be found on the Introduction to Linear...

Tested for the rigors of competition, REV Mecanum Wheels are steel plates with rollers supported by ball bearings allowing for the perfect combination of wheel rigidity and roller movement. Included in the set of wheels are Universal Hex Adapter making...

Updated version of our popular Linear Motion Kit. This kit has been redesigned to be even easier for teams to use with REV 15mm Extrusion to create compact linear slides. New additions to the kit include End Cap pieces to keep lift stages in place,...

A custom-designed tool that allows teams to easily break and re-assemble #25 chain. The mandrel is used to push out the chain pin. If using connecting links, the pin can be completely removed, but the depth guide screw allows the option of partially...

Now legal for both FTC and FRC! Blinkin makes adding LEDs to your robot as simple as driving a motor. Chose the pattern you want and give it the corresponding PWM signal. The REV Robotics Blinkin LED Driver is a compact LED driver module that simplifies...

For smaller applications the REV Building System also comes in a 15mm x 15mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. This product is a 4-pack of 420mm pieces of extrusion, an appropriate...

Charger for use with our 12V Slim Battery. The output is wired with an XT30 male connector for charging. For the input, the battery charger has an IEC C13 power cord to standard, grounded, North America wall outlet plug (NEMA 5-15). *Do not...

Add this switch between your battery and Expansion Hub to have convenient on/off control of your robot. We recommend mounting the switch slightly recessed from the outside of your robot so that it's not accidentally turned off by another robot during a...

The Servo Power Module is a 6V 90W power injector that enables the use of high-power RC servos in applications where a robot controller cannot directly provide adequate power.  The Servo Power Unit passes through input signals unaltered while...

This 10-cell, 12V 3000mAh battery has a low profile configuration to make it easier to mount on a robot. The Slim Battery pack is wired with an XT30 male connector and an inline 20A replaceable ATM fuse. XT30 to Tamiya Adapter no longer automatically...

The REV Robotics Smart Robot Servo (SRS) is a configurable metal-geared servo that takes the guesswork out of aligning and adjusting servo based mechanisms. One SRS can be used as a standard angular servo, a custom angular servo, and a continuous...

REV 45mm x 15mm C Channel has a 45mm x 15mm rectangular profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsional strength is required. The 45mm wide side of the channel...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

The HD Hex series motors and gearboxes feature integrated encoders and power that plug right into the Control Hub (REV-31-1595) and Expansion Hub (REV-31-1153). The gearbox options feature 5mm Hex output or coupler making it easy to connect gears,...

This product has been discontinued as of 07/15/2024 and replaced with (REV-31-2983) REV USB PS4 Compatible Gamepad. The Etpark Wired Controller is a legal gamepad for the FIRST Tech Challenge program. This controller...

REV Building System also comes in a 15mm x 30mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. Use the 15mm x 30mm extrusion when more strength is needed for an application. Features All holes can be...