Competition

The NEO Vortex is a high-power, high-performance, and high-resolution sensored brushless motor that is compatible with the REV ION System. It features a dockable controller interface that can be mounted directly to the SPARK Flex Motor Controller or our...

The SPARK Flex is a new smart motor controller that is compatible with the REV ION System. Its dockable form factor allows for the direct mounting onto a NEO Vortex, simplifying wiring while maintaining flexibility. Improving upon the...

The Vortex Shaft - MAXSwerve Integrated Key is compatible with the REV ION System and gives users the ability to drive a MAXSwerve Module without the need for the MAXSwerve Key. This eliminates a potential point of failure in the MAXSwerve since the key...

The Vortex Shaft - Falcon Compatible Spline is compatible with the REV ION System and gives users the ability to drive components that have a falcon spline bore. *Falcon is not a REV trademark. Featuring a 1/2in hex section that drives the shaft and a...

The 8mm Vortex Shaft, compatible with the REV ION System, empowers you to utilize the NEO Vortex Brushless Motor with any 8mm keyed shaft component. This interchangeability also means that the NEO Vortex matches the output of a NEO Brushless Motor V1.1,...

The Vortex MAXPlanetary Input Kit is compatible with the REV ION System and gives users the ability to mount a MAXPlanetary Gearbox directly to your NEO Vortex Brushless Motor and SPARK Flex Motor Controller. Working seamlessly with the MAXPlanetary...

The Flex Dock transforms the SPARK Flex (REV-11-2159) into a standalone motor controller, supporting REV brushless motors and virtually any 12V brushed DC motor by providing standard phase wire outputs. The 6-pin JST PH encoder port is compatible with...

The NEO Vortex Solo Adapter, allows teams to seamlessly integrate the NEO Vortex Brushless Motor with a SPARK MAX Motor Controller. This adapter breaks out the motor sensor connector and phase wire connections. While the NEO Vortex Solo Adapter allows...

The 3in MAXSwerve Module is the smallest and lightest swerve module designed for FRC Teams. Leveraging many parts of the REV ION System, MAXSwerve aims to reduce the complexity traditionally associated with swerve drivetrains. The module features a 3in...

Updated for the 2024-25 season, the FTC Starter Kit V3.1 introduces new and existing REV DUO products so teams can maximize their build. The FTC Starter Kit V3.1 was developed based on feedback from teams to include more of the essential...

The DUO Control Bundle offers basic FTC-legal control system components to get an existing robot up and running. Pair this bundle with the DUO EDU Mechanical Kit (REV-45-2708) to get started with our all-new curriculum, Intro to Robotics I (REV-77-2707),...

Featuring the REV Driver Hub, an easy to use, dependable, and durable device designed for interfacing with the Control Hub. Featuring an Android operating system and built-in dual band Wi-Fi, this device makes getting your robot running easier than...

An individual cartridge for the MAXPlanetary System. This cartridge is a 9:1 gear reduction.With a 9:1 reduction in a single stage cartridge you will save significant space and weight in your builds that demand the higher reduction!The MAXPlanetary...

The 2 Motor Gearbox - Through Bore is compatible with the REV ION System. This two motor into one output gearbox allows the user to adjust the gear ratio by changing pinion and cluster gear (12:60, 18:54, 24:48, or 36:36). The output shaft is 1/2in...

Designed for use with the REV ION System and with an efficient right-angle configuration, the MAX 90 Degree Gearbox offers a robust and high-performance solution to building a more compact robot. Connect the MAX 90 Degree Gearbox to the MAXPlanetary...

The REV Power Distribution Hub (PDH) is the latest evolution in power distribution for the FIRST Robotics Competition (FRC).  With 20 high-current (40A max) channels, 3 low-current (15A max), and 1 switchable low-current channel, the PDH...

ION #25 Sprockets are compatible with the REV ION System and designed for use with #25 Roller chain. #25 Plate Sprockets: Featuring MAXSpline and a 2in bolt circle that patterns outward radially, allowing for bolting to structure easily. #25 Hub...

3/8 Nut Strips are compatible with the REV ION System featuring convenient 1/2in spaced #10-32 threaded holes that are inline with each other allowing easy fastening of aligned plates and structure without the need for individual nuts...

20DP Gears are compatible with the REV ION System and come in a wide range of sizes and bores. Larger gears feature #10 clearance holes arranged in a 2-inch bolt circle pattern and MAXTube mounting pattern. A notch on the bore provides an easy...

20DP Gears are compatible with the REV ION System and come in a wide range of sizes and bores. Larger gears feature #10 clearance holes arranged in a 2-inch bolt circle pattern. A notch on the bore provides an easy visual indicator to ensure gears on the...

The REV USB PS4 Compatible Gamepad is compatible with both the REV DUO and REV ION Systems. Plug the REV Gamepad directly into a Driver Hub to enable feature rich control of your robot. Additionally, when plugged into a PC, it offers an Xbox...

The REV Pneumatic Hub is a standalone module that is capable of switching both 12V and 24V pneumatic solenoid valves. The Pneumatic Hub features 16 solenoid channels which allow for up to 16 single-acting solenoids, 8 double-acting solenoids, or a...

The MAXPlanetary Base Kit (REV-25-2109) is the entry point into using the MAXPlanetary System. This base kit includes a universal input stage, 1/2in hex socket output, hardware pack, 8mm keyed input coupler kit, and a 1/2in rounded hex shaft. Purchase a...

The REV UltraPlanetary Gearbox Kit is the entry point into using the REV UltraPlanetary System. The kit comes with UltraPlanetary Cartridges to support six different final gear reductions ranging from nominally 3:1 to 60:1 allowing for the right amount...

MAX Pattern Plates are compatible with the REV ION System and feature the all-new MAX Pattern: a MAXSpline bore surrounded by #10 clearance holes on a 0.5in grid. The plates are available in various lengths, with the pattern repeating every 2in...

MAXSpline Spacers are compatible with the REV ION System and can be used on the shaft as a spacer; they also work as spacers between wheels and sprockets, etc. Specifications Material: POM (Acetal/Delrin) OD: 1.50in Weights &...

#10 Spacers are compatible with the REV ION System and are an accurate way to space structural components like plates, brackets, or tubes apart on #10 screws. Can also be used to to space motion components like gearboxes away from their mounting...

1/2in Rounded Hex Shafts are compatible with the REV ION System and are a ready-to-use length of hex shaft that have been cut to length and have the ends tapped. The ends are tapped #10-32 in order to accept a screw and washer or shaft collar. The 1/2in...

#10-32 Standoffs are compatible with the REV ION System and provide spacing for mounting key items on your robot. These standoffs are tapped on each end for a #10-32 thread and have a 3/8in flat to flat dimension, similar to a #10-32 nut...

The REV Radio Power Module is designed to keep one of the most critical system components, the OpenMesh OM5P-AC WiFi radio, powered in the toughest moments of the competition. Traditional barrel jacks easily work themselves loose and often require hacks...

An individual cartridge for the MAXPlanetary System. This cartridge is a 5:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

An individual cartridge for the MAXPlanetary System. This cartridge is a 4:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

An individual cartridge for the MAXPlanetary System. This cartridge is a 3:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

The Elevator Bearing Blocks family offers reliable, versatile solutions for creating linear motion in elevator systems using MAXTube. Both the original Elevator Bearing Block and the Clamping Elevator Bearing Block provide teams with the flexibility to...

MAXTube Endcaps are designed for seamless integration with the REV ION System, providing a simple and effective solution for joining two or more MAXTube extrusions. These endcaps are pre-tapped for #10-32 hardware, ensuring quick assembly and reliable...

The 3in MAXSwerve V1 to V1.1 Upgrade Kit brings a simplified motor keying approach to the main drive motor allowing for easier installation on the 3in MAXSwerve Module (REV-21-3005). A new version of the Encoder Bridge is included to adapt to the use of...

The MAXLift #25 Chain Attachment Plate is a durable yet lightweight aluminum bracket designed for seamless use with the REV ION system within the MAXLift family of products. It simplifies mounting and assembly for elevator and lift systems. Featuring...

3/16in Rivets are compatible with the REV ION System are perfect for a variety of applications where a strong, permanent joint is required. Place the rivet into a hole from a single side (a “blind” hole) and then use a rivet...

Steel hardware of the appropriate size to work with the REV ION System. Length measured from tip to underside of screw head. Documentation ION Build System Guide Hardware Basics Onshape Application Examples Product...

Steel hardware of the appropriate size to work with the REV ION System. Length measured from tip to underside of screw head. Documentation ION Build System Guide Hardware Basics Onshape Application Examples Product...

ION Servo Accessories allow for easy integration into REV ION System. Mount a hobby sided servo, such as the REV Smart Robot Servo, on a 1/2in pitch. Using the adapters, you can convert a servo to a 1/2in Hex shaft for use with all other...

Zinc plated steel nuts compatible with all REV M3 screws or bolts. Contains a nylon insert which increases grip on screw, reducing the chance of the nut loosening over time. Does NOT fit in the channel of our REV DUO 15mm Extrusion System...

The 8mm Shaft Spacer is compatible with the REV ION System and is a convenient way to space pinions and gears along the shaft of the NEO Brushless Motor. The 8mm Shaft Spacer is bigger than the 1/2in Hex Adapter and can help keep...

#10-32 Shaft End Screw V1 and V2 are compatible with the REV ION System and are used to retain parts on any ION hex shaft instead of shaft collars. 1/2in Rounded Hex Shafts in various lengths are available and come tapped with #10-32 holes. The...

The 3in MAXSwerve Module - Kraken Input Kit is a versatile add-on designed to integrate the Kraken X60 motor with the 3in MAXSwerve Module. This kit features a modified 14T pinion gear for seamless power transfer with the 8mm - 15T spline. It includes a...

The MAXPlanetary Kraken X44 & Minion Input Kit is a comprehensive solution for adapting Kraken X44 or Minion motors to the MAXPlanetary system. This kit includes the [REV-21-4444] MAXPlanetary Kraken X44 & Minion Adapter Plate, designed with...

GT2 3mm Pitch Belts are compatible with both the REV ION System and the REV DUO System. These belts go hand in hand with GT2 timing pulleys. Use belts and pulleys in tight to fit areas where adjustment is difficult. Specifications Pitch: 3mm Width:...

Bearings 1/2in Hex Bearing - Flanged - 1.125in OD - 4 Pack (REV-21-1915-PK4) This flanged bearing provides a reliable way to locate and support a 1/2in hex shaft or 1/2in rounded hex shaft while it rotates. The flange ensures secure installation in...