The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The REV Robotics Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will...

Easily connect multiple devices to your robot battery with the XT30 Power Distribution Block. Allows for clean, compact wiring of all your XT30-connected devices. Compatible with: Expansion Hub, Blinkin LED Driver, SPARKmini, Servo Power Module, and many...

The 3in MAXSwerve Aluminum Wheel was designed for the 3in MAXSwerve Module. You can attach your favorite tread material to this wheel. REV recommends rough top conveyor belting. A cut template for the wheel tread is available below.  ...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications REV-11-1275-PK4: Length: 90cm (35.5in) REV-11-3327: Length: 30cm (11.81in)

The 3in MAXSwerve Module Wheel Hardware Pack was designed for the 3in MAXSwerve Module. This kit is for FRC teams looking to streamline their wheel maintenance at competitions. With this kit, teams can pre-build their wheel assemblies, making...

This product is a 6:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 5:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 3:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 2:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 1:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

The Mecanum Drivetrain Kit V2 provides everything needed to build an omnidirectional drivetrain. Featuring Ultra 90 Degree Gearboxes, this kit positions the motors directly within the drive channels to maximize internal space for mechanisms and...

The MK Battery ES17-12 is commonly used in FIRST Robotics Competition robots. Specifications Manufacturer: MK Battery Voltage: 12V Capacity: 18AH (20 Hour Rate) Product Dimensions: 7.13in x 2.99in x 6.57in Weight: 12.89lbs Documentation MK...

Dead Axle Tube is compatible with the REV ION System and can be used with 3/4in Needle Bearing Carrier (REV-21-2385) and MAXSpline Shaft (REV-21-2520) as the dead axle in a dead axle roller. Can also be used with custom rollers and as...

The 1in Pivot Joint is compatible with the REV ION System. Create a pivot joint at the end of a piece of MAXTube - 1x1 with Grid Structure. Specifications Material: POM (Acetal/Delrin) Documentation REV ION Build System Documentation Introduction...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0. Applications ...

The WAGO 221 Inline Splicing Connector is a robust and easy to use splicing connector that makes fiddling with hard-to-master crimp-style connectors a thing of the past. Simply lift the lever up, insert the stripped wire, and push the lever back down to...

The REV Mini Power Module (MPM) is a compact power distribution module that allows you to securely and quickly power peripheral devices to your robot. Need more low-current channels on your PDH? Wire the MPM to one of the high-current channels on the PDH...

The MAXPlanetary 550 Input Kit gives users the ability to use 550 size motors with the MAXPlanetary System.  Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that can come loose...

The MAXPlanetary 775 Input Kit gives users the ability to use 775 size motors (775pro or AM RedLine) with the MAXPlanetary System. Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that...